loading

How To Maintain The Impeller When Using The Slurry Pump To Reduce Wear?

The use of slurry pumps is becoming more and more widespread, and inevitably, accessories usually wear during operation, and are often used to improve the internal flow state of the pump, improve the wear resistance of the runner material, and improve the surface finish of the runner to reduce wear.According to tribological classification, wear belongs to two body wear, namely, corrosive hard solid particles and the surface of the runner component constitute friction.Their respective characteristics and contact surfaces determine the type and degree of wear of the runner component. Therefore, the main factors that cause wear of the accessories impeller can be summarized as follows.  1. Properties of solids in slag and slag.2. The movement characteristics of the solid and liquid phases in the pump, that is, the contact between the solid and liquid phase and the liquid phase and the surface of the flow path component.3. Material characteristics of the pump's runner component.In order to maintain good working efficiency of the slurry pump, this is closely related to the maintenance of accessories. So what should we pay attention to in processing?1. When rotating the impeller, the gap between the machine tool, tool holder and tool holder should be adjusted to the smallest position as possible to ensure that the entire machine tool processing system has sufficient rigidity.The chamfer of the workpiece should be as large as possible so that the turning tip can be cut in and out smoothly during the turning process, thereby minimizing the impact on the tool tip and the cracks in the workpiece as much as possible.2. A reasonable cutting tool geometric angle is conducive to improving the durability of the slurry pump.The grinding wheel should be stable and sharp during grinding, and the saw blade should be ground into a straight line without sawing teeth.

GET IN TOUCH WITH Us
recommended articles
Horizontal Slurry Pumps: Principles & Application
Because they offer longevity, efficiency, and adaptability, horizontal slurry pumps are crucial for sectors handling abrasive slurries. Knowing their values, applications, and maintenance needs allows businesses to maximize performance and reduce expenses.
Commissioning of Slurry pumps
Slurry pump commissioning must be strictly conducted in accordance with established procedures: Prior to startup, first activate the shaft seal water and adjust it to the specified pressure. Fully open the inlet valve. For non-backflow pumps, water must be injected. After opening the outlet valve to one-quarter, initiate startup; During operation, monitor flow rate, head, current, vibration, and bearing temperature (temperature rise ≤35°C, maximum ≤75°C). Mechanical seal leakage should be ≤3-5 ml/h. Before stopping the pump, flush with clean water for 30 minutes, close the outlet valve first, then shut down the pump, and finally close the shaft seal water and inlet valve. It is strictly prohibited to fully open the outlet valve when stopping the pump to prevent water hammer. Throughout the entire trial operation process, ensure that parameters remain stable, avoid cavitation and overload conditions, to ensure safe operation of the equipment.
Common Problems During Feeding of Slurry Pumps
When a slurry pump malfunctions during operation, the first step is to identify the cause of the failure. Corresponding repair measures should be taken based on the characteristics of the failure and maintenance experience.
Aspects to Pay Attention to for Slurry Pumps to Run Stably and Efficiently in Series

The advantage of slurry pumps in series is that multiple pumps are arranged in one pump station, which is convenient for installation, maintenance, operation and management, with a total low cost, it can realize overall automatic management. The following aspects should be noted when selecting slurry pumps in series:
The Hazards to Slurry Pumps if Running in a Low Flow Area for a Long Time
The slurry pumps we often use are a type of centrifugal pump. It mainly drives the slurry mixture to rotate through the high-speed rotating impeller blades, and throws out the slurry to achieve the purpose of transportation.
The methods for adjustment the flowrate of slurry pumps
The flowrate adjustment method of slurry pump can be selected in various ways according to different needs and occasions. The following are some common flowrate adjustment methods:
Five Main Reasons for the Blockage of Slurry Pumps
Uneven medium density is one of the reasons for the blockage of slurry pumps. When the medium density is uneven, the pump may vibrate at the beginning of the startup, but this vibration usually disappears when the pump starts normally.
no data
Ready to work with us ?

Our professional slurry pump team is always At your services.

We are engaged in the manufacturing and producing of heavy duty and severe duty slurry pumps and spare parts.
Every CNSME product comes with an industryeading promise to weather years of memories.
Safe, fast, and on-time delivery.
no data
Contact Us

Contact: Ms.Serena Zhang

Tel: +86 13333119820

Email: sales@cnsmepump.com 

WhatsApp: +86 13333119820

Add: 260# West Huaian Road, Shijiazhuang, Hebei, China. 050051.

Download
Copyright © 2025 Shijiazhuang Minerals Equipment Co., Ltd.  | Sitemap

Send your inquiry

弹窗效果
Customer service
detect