loading

How To Solve The Problem Of Insufficient Flow In The Hydraulic System Of The Slurry Pump?

When using the slurry pump, sometimes encounters insufficient flow in the hydraulic system. Don’t worry, you can refer to the following content for analysis and solution.If the impeller, water inlet and outlet pipe are blocked, please clean the impeller or water pipe.If the impeller is severely worn, it should be replaced.If the packing port leaks, the packing should be tightly pressed.The power speed of the slurry pump does not match or the belt slips, resulting in a reduced speed; the installation angle of the axial flow pump blade is too small; the head is insufficient, the pipe is too long or the pipe is bent at a right angle; the suction process is too high, the valves are partially blocked at the bottom of the pipe and impeller or impeller defects; the outlet pipe is seriously leaking.Solution: Restore the rated speed, remove grease on the belt, adjust the tightness of the belt; adjust the blade angle, reduce the installation position of the water pump, shorten the pipeline or change the curvature of the pipeline; seal the leakage of the water pump, press the filler; remove blockage and replace the impeller; replace the leakage reduction ring to prevent leakage.  1. The oil pump does not drain; check and repair the oil pump.2. The pressure of the sequence valve is too low or the slide valve is stuck in the open position; repair the sequence valve.3. The oil filter is blocked; clean the oil filter.4. The oil level in the oil tank is too low, and the oil pump is drained; replenish oil.5. The viscosity of hydraulic oil is too high and it is difficult to absorb oil; change the engine oil or increase the engine oil temperature.6. The internal parts of the slurry pump are seriously worn, with large internal leakage, and the pressure and flow cannot reach the rated value. Repair or replace the oil pump.

GET IN TOUCH WITH Us
recommended articles
Horizontal Slurry Pumps: Principles & Application
Because they offer longevity, efficiency, and adaptability, horizontal slurry pumps are crucial for sectors handling abrasive slurries. Knowing their values, applications, and maintenance needs allows businesses to maximize performance and reduce expenses.
Commissioning of Slurry pumps
Slurry pump commissioning must be strictly conducted in accordance with established procedures: Prior to startup, first activate the shaft seal water and adjust it to the specified pressure. Fully open the inlet valve. For non-backflow pumps, water must be injected. After opening the outlet valve to one-quarter, initiate startup; During operation, monitor flow rate, head, current, vibration, and bearing temperature (temperature rise ≤35°C, maximum ≤75°C). Mechanical seal leakage should be ≤3-5 ml/h. Before stopping the pump, flush with clean water for 30 minutes, close the outlet valve first, then shut down the pump, and finally close the shaft seal water and inlet valve. It is strictly prohibited to fully open the outlet valve when stopping the pump to prevent water hammer. Throughout the entire trial operation process, ensure that parameters remain stable, avoid cavitation and overload conditions, to ensure safe operation of the equipment.
Common Problems During Feeding of Slurry Pumps
When a slurry pump malfunctions during operation, the first step is to identify the cause of the failure. Corresponding repair measures should be taken based on the characteristics of the failure and maintenance experience.
Aspects to Pay Attention to for Slurry Pumps to Run Stably and Efficiently in Series

The advantage of slurry pumps in series is that multiple pumps are arranged in one pump station, which is convenient for installation, maintenance, operation and management, with a total low cost, it can realize overall automatic management. The following aspects should be noted when selecting slurry pumps in series:
The Hazards to Slurry Pumps if Running in a Low Flow Area for a Long Time
The slurry pumps we often use are a type of centrifugal pump. It mainly drives the slurry mixture to rotate through the high-speed rotating impeller blades, and throws out the slurry to achieve the purpose of transportation.
The methods for adjustment the flowrate of slurry pumps
The flowrate adjustment method of slurry pump can be selected in various ways according to different needs and occasions. The following are some common flowrate adjustment methods:
Five Main Reasons for the Blockage of Slurry Pumps
Uneven medium density is one of the reasons for the blockage of slurry pumps. When the medium density is uneven, the pump may vibrate at the beginning of the startup, but this vibration usually disappears when the pump starts normally.
no data
Ready to work with us ?

Our professional slurry pump team is always At your services.

We are engaged in the manufacturing and producing of heavy duty and severe duty slurry pumps and spare parts.
Every CNSME product comes with an industryeading promise to weather years of memories.
Safe, fast, and on-time delivery.
no data
Contact Us

Contact: Ms.Serena Zhang

Tel: +86 13333119820

Email: sales@cnsmepump.com 

WhatsApp: +86 13333119820

Add: 260# West Huaian Road, Shijiazhuang, Hebei, China. 050051.

Download
Copyright © 2025 Shijiazhuang Minerals Equipment Co., Ltd.  | Sitemap

Send your inquiry

弹窗效果
Customer service
detect