loading

The Slurry Pump Casing Is Worn, And Timely Repair Is Very Important

  As the long-term use of slurry pumps, some parts will inevitably cause certain wear, and the pump shell is one of them.If the wear is not serious, you can continue working.If the equipment is worn seriously, it may cause the pump housing to crack and damage the entire equipment body.At this point, we need to repair the damaged part of the device.Let's see how to fix them.1. Before repairing the worn parts of the pump housing, the impeller must be removed to leave an operable space, and on-site dust protection and safety protection must be done.2. First observe the severity of the wear of the pump case, and then consider which method to repair it.3. Pre-weld the leakage of the pump body to strengthen the leakage points and weak points, and then rinse the pump shell with a lot of clean water to remove the paint remaining on the surface.4. Afterwards, the surface of the pump shell is blasted to remove the oxide layer, increase the roughness of the pump shell repair surface, and increase the adhesion of the repair material.5. When repairing the pump housing of the slurry pump, use excellent materials to spray, clean the surface before the spectrum, and then start spraying.6. When spraying, the paint must be sprayed correctly in a certain proportion.7. After repair, perform secondary repair to achieve the effect of no defects on the entire protective layer surface.8. After the repair is completed, cure by heating to fully utilize the performance of the restoration material.Many users don’t care if the slurry pump housing is worn and they don’t feel anything.However, if left to develop, long-term wear will seriously affect the normal operation of the equipment.Therefore, I would like to remind everyone that when the pump case is found to be worn, we must find out the cause and solve it in time to avoid the situation from worsening and the equipment being unusable.

GET IN TOUCH WITH Us
recommended articles
Horizontal Slurry Pumps: Principles & Application
Because they offer longevity, efficiency, and adaptability, horizontal slurry pumps are crucial for sectors handling abrasive slurries. Knowing their values, applications, and maintenance needs allows businesses to maximize performance and reduce expenses.
Commissioning of Slurry pumps
Slurry pump commissioning must be strictly conducted in accordance with established procedures: Prior to startup, first activate the shaft seal water and adjust it to the specified pressure. Fully open the inlet valve. For non-backflow pumps, water must be injected. After opening the outlet valve to one-quarter, initiate startup; During operation, monitor flow rate, head, current, vibration, and bearing temperature (temperature rise ≤35°C, maximum ≤75°C). Mechanical seal leakage should be ≤3-5 ml/h. Before stopping the pump, flush with clean water for 30 minutes, close the outlet valve first, then shut down the pump, and finally close the shaft seal water and inlet valve. It is strictly prohibited to fully open the outlet valve when stopping the pump to prevent water hammer. Throughout the entire trial operation process, ensure that parameters remain stable, avoid cavitation and overload conditions, to ensure safe operation of the equipment.
Common Problems During Feeding of Slurry Pumps
When a slurry pump malfunctions during operation, the first step is to identify the cause of the failure. Corresponding repair measures should be taken based on the characteristics of the failure and maintenance experience.
Aspects to Pay Attention to for Slurry Pumps to Run Stably and Efficiently in Series

The advantage of slurry pumps in series is that multiple pumps are arranged in one pump station, which is convenient for installation, maintenance, operation and management, with a total low cost, it can realize overall automatic management. The following aspects should be noted when selecting slurry pumps in series:
The Hazards to Slurry Pumps if Running in a Low Flow Area for a Long Time
The slurry pumps we often use are a type of centrifugal pump. It mainly drives the slurry mixture to rotate through the high-speed rotating impeller blades, and throws out the slurry to achieve the purpose of transportation.
The methods for adjustment the flowrate of slurry pumps
The flowrate adjustment method of slurry pump can be selected in various ways according to different needs and occasions. The following are some common flowrate adjustment methods:
Five Main Reasons for the Blockage of Slurry Pumps
Uneven medium density is one of the reasons for the blockage of slurry pumps. When the medium density is uneven, the pump may vibrate at the beginning of the startup, but this vibration usually disappears when the pump starts normally.
no data
Ready to work with us ?

Our professional slurry pump team is always At your services.

We are engaged in the manufacturing and producing of heavy duty and severe duty slurry pumps and spare parts.
Every CNSME product comes with an industryeading promise to weather years of memories.
Safe, fast, and on-time delivery.
no data
Contact Us

Contact: Ms.Serena Zhang

Tel: +86 13333119820

Email: sales@cnsmepump.com 

WhatsApp: +86 13333119820

Add: 260# West Huaian Road, Shijiazhuang, Hebei, China. 050051.

Download
Copyright © 2025 Shijiazhuang Minerals Equipment Co., Ltd.  | Sitemap

Send your inquiry

弹窗效果
Customer service
detect