These Two Points In The Use Of The Slurry Pump Will Get Twice The Result With Half The Effort

2025-06-21

CNSME PUMP

　　The start-up and operation and monitoring of the slurry pump are very important for use. Timely handling of faults can effectively avoid damage to the slurry pump and extend its service life.This is very important for users of slurry pumps. We conducted a check before starting, and it is necessary to monitor whether the operation is smooth and stable after starting.So what should we do for the start and monitoring of the slurry pump?Let’s take a look with the editor!Starting and monitoring of slurry pump 1. Before operation, the slurry pump should fill the pool with clean water, open the pump inlet valve, and close the pump outlet valve.2. Then start the pump, slowly open the outlet valve of the pump after the pump starts. 3. At the same time, release the slurry into the pool according to the required amount. 4. The size and speed of the pump outlet valve should be controlled by the fact that the pump does not vibrate and the motor does not exceed the rated current until the page can be stable at 0.5-1 meter above the inlet pipe. 5. Regularly check and adjust the filler gland in time during operation. 6. Pay attention to check the operation of the bearing and do not enter the mine. If the bearing enters the mine, it must be stopped immediately for cleaning and oil change. 7. The bearing temperature must not exceed 75℃. 8. If the bearing is heated, the pump can be stopped for cooling.Run again. If the heat is still severe, the machine must be shut down. 9. Timely adjust the ore supply or water or the outlet valve of the pump. Under any circumstances, the pump is prohibited from evacuating and causing vibration of the pump. 10. No block material is allowed to enter the pump to prevent blockage or damage the pump lining. 11. Recharge in time according to the oil level of the pump. 12. Check whether the water sealing pressure is normal, whether the water volume is blocked, whether the water is sufficient, and whether the water quality is clean. 13. Check the lubricating oil level in each part, whether the oil temperature is normal, the lubricating oil must be clear, and the oil temperature must not exceed 50 degrees. 14. Pay attention to whether the motor is working current is normal and whether the motor has abnormal noise.

GET IN TOUCH WITH Us

Pumps for Quartz Sand_Rubber-Lined Slurry Pumps in Quartz Sand Beneficiation Equipment

Quartz sand beneficiation focuses primarily on purification, a technically challenging separation process aimed at removing minor or trace impurities from quartz sand to produce refined quartz sand or high-purity quartz sand. Common purification techniques employed domestically and internationally include: Washing, Classification & Desliming, Scrubbing, Magnetic Separation, Flotation, Acid Leaching, and Microbial Leaching.

The Ultimate Guide to Slurry Pumps: Types and Applications

Selecting the right slurry pump ensures efficient performance, especially when dealing with high-volume and abrasive slurries. The ideal pump depends on the application, material compatibility, and operational demands.

Diagnosis Methods for Cavitation in Warman Slurry Pumps

The following techniques can be used to determine whether cavitation is occurring in a slurry pump:a. Ultrasonic testing b. External noise monitoring c. Vibration analysis

Horizontal Slurry Pumps: Principles & Application

Because they offer longevity, efficiency, and adaptability, horizontal slurry pumps are crucial for sectors handling abrasive slurries. Knowing their values, applications, and maintenance needs allows businesses to maximize performance and reduce expenses.

Commissioning of Slurry pumps

Slurry pump commissioning must be strictly conducted in accordance with established procedures: Prior to startup, first activate the shaft seal water and adjust it to the specified pressure. Fully open the inlet valve. For non-backflow pumps, water must be injected. After opening the outlet valve to one-quarter, initiate startup; During operation, monitor flow rate, head, current, vibration, and bearing temperature (temperature rise ≤35°C, maximum ≤75°C). Mechanical seal leakage should be ≤3-5 ml/h. Before stopping the pump, flush with clean water for 30 minutes, close the outlet valve first, then shut down the pump, and finally close the shaft seal water and inlet valve. It is strictly prohibited to fully open the outlet valve when stopping the pump to prevent water hammer. Throughout the entire trial operation process, ensure that parameters remain stable, avoid cavitation and overload conditions, to ensure safe operation of the equipment.

Common Problems During Feeding of Slurry Pumps

When a slurry pump malfunctions during operation, the first step is to identify the cause of the failure. Corresponding repair measures should be taken based on the characteristics of the failure and maintenance experience.

Aspects to Pay Attention to for Slurry Pumps to Run Stably and Efficiently in Series

The advantage of slurry pumps in series is that multiple pumps are arranged in one pump station, which is convenient for installation, maintenance, operation and management, with a total low cost, it can realize overall automatic management. The following aspects should be noted when selecting slurry pumps in series:

The Hazards to Slurry Pumps if Running in a Low Flow Area for a Long Time

The slurry pumps we often use are a type of centrifugal pump. It mainly drives the slurry mixture to rotate through the high-speed rotating impeller blades, and throws out the slurry to achieve the purpose of transportation.

The methods for adjustment the flowrate of slurry pumps

The flowrate adjustment method of slurry pump can be selected in various ways according to different needs and occasions. The following are some common flowrate adjustment methods:

Five Main Reasons for the Blockage of Slurry Pumps

Uneven medium density is one of the reasons for the blockage of slurry pumps. When the medium density is uneven, the pump may vibrate at the beginning of the startup, but this vibration usually disappears when the pump starts normally.